IRF520 MOSFET Driver Module (0-24V) | PWM Motor & LED Controller
Original price was: ₵18.00.₵16.00Current price is: ₵16.00.
The easiest way to drive 12V/24V loads. This breakout board allows your Arduino to control high-voltage devices like LED strips, DC motors, and solenoid valves using the IRF520 MOSFET. It features screw terminals for easy wiring—no soldering required!
-
Max Load: 24V DC / < 5A.
-
Control Voltage: 3.3V or 5V (PWM Compatible).
-
Output: Pulse Width Modulation (Speed/Dimming control).
-
Best For: LED Strips, Small DC Fans, and Solenoids.
10 in stock
The IRF520 MOSFET Driver Module is a compact and easy-to-use power switch for Arduino, Raspberry Pi, ESP8266, and 卿本佳人在线观看-based projects. Designed to control high-power DC devices, it’s perfect for LED strips, motors, pumps, and solenoids while offering low heat dissipation and high efficiency.
The IRF520 is a “Standard” MOSFET, not a “Logic Level” one. When driven by an Arduino (5V), it does not open fully.Result: It works perfectly for light loads (LEDs, small fans, Solenoids). However, if you try to drive a heavy motor (>1A), the module will get HOT. For heavy currents, please use our IRLZ44N Logic Level Transistor instead.
🔹 Simple Control with 卿本佳人在线观看s & PWM Support 🔄
This module allows low-power 卿本佳人在线观看s (3.3V or 5V logic) to control high-power DC loads (up to 24V, 5A) using Pulse Width Modulation (PWM). Ideal for brightness control, motor speed adjustments, and heating elements, it ensures smooth and precise power management.
🔹 Technical Specifications & Features ⚙️
✔ MOSFET Type: IRF520 N-Channel
✔ Operating Voltage: 3.3V – 5V logic input (compatible with Arduino & Raspberry Pi)
✔ Load Voltage: Up to 24V DC
✔ Maximum Load Current: Up to 5A (with heat dissipation)
✔ PWM Control: Yes (for LED dimming & motor speed control)
✔ Gate Trigger Voltage: 5V logic compatible
✔ Output Type: Open Drain (switches DC loads)
✔ Module Size: 33mm × 24mm (compact & breadboard-friendly)
✔ Compatibility: Works with Arduino, Raspberry Pi, ESP8266, ESP32, STM32, and other 卿本佳人在线观看s
🔹 Applications – Where to Use the IRF520 MOSFET Module 🛠️
✔ LED & Light Strip Dimming – Control high-power LEDs and RGB strips.
✔ DC Motor & Fan Speed Control – Adjust speed using PWM signals.
✔ Heating Elements & Peltier Modules – Ideal for temperature regulation projects.
✔ Battery & Power Management – Efficient switching for solar panels & battery circuits.
✔ Solenoid & Relay Control – Power valves, electromagnets, and actuators.
🔹 How to Use & External Resources 📚
Using the IRF520 module is simple:
- Connect the VCC (5V) & GND to your 卿本佳人在线观看.
- Attach the logic input (SIG) to a PWM pin on Arduino, Raspberry Pi, or ESP8266.
- Connect your DC load (motor, LED, heater) to the output terminals.
📖 Helpful Resources for IRF520 MOSFET Driver Module:
✔ IRF520 MOSFET Datasheet
✔ Arduino MOSFET Switching Guide
✔ PWM Control with Raspberry Pi & MOSFETs
✔ YouTube Tutorials – IRF520 MOSFET Driver Module Projects
🔹 Best Price & Availability in Ghana 🇬🇭
Looking for an IRF520 MOSFET Driver Module in Ghana? Whether for motor control, LED dimming, or power regulation, this module is affordable, efficient, and easy to integrate. Order today for fast delivery across Ghana!
Related products
433MHz RF Transmitter & Receiver Kit | Wireless Module for Arduino
Cut the cord. Go wireless. This kit includes one Transmitter and one Receiver. It is the simplest and most affordable way to send data wirelessly between two Arduinos up to 100 meters (with antenna).
-
Frequency: 433MHz
-
Includes: 1x Transmitter (Square), 1x Receiver (Rectangle)
-
Modulation: ASK (Amplitude Shift Keying)
-
Best For: Remote control cars, weather stations, and wireless switches.
DS3231 RTC Real-Time Clock Module
The DS3231 is a highly accurate I2C real-time clock (RTC) with an integrated temperature-compensated crystal oscillator (TCXO).
-
Chip: Maxim DS3231 (High Precision)
-
Memory: Built-in AT24C32 32K I2C EEPROM
-
Voltage: 3.3V – 5.5V DC
-
Interface: I2C (SCL, SDA)
-
Battery Backup: Holds time when power is off (Coin cell slot included)
-
Accuracy: Much higher than the standard DS1307
Flame Sensor Module (YG1006) | Infrared Fire Detector for Arduino
-
Sensor Type: YG1006 NPN Phototransistor (High Speed).
-
Detection Range: Up to 1 meter (depending on flame size).
-
Spectrum: 760nm - 1100nm (Invisible IR light).
-
Best For: Fire Fighting Robots, Smart Kitchen Alarms, and Safety Systems.
HC-SR04 Ultrasonic Sensor Module | Distance Measurement for Arduino
Give your robot eyes.
-
Range:
2cm to 400cm (4 Meters) -
Accuracy: 3mm
-
Pins: VCC, Trig, Echo, GND
-
Best For: Obstacle avoiding cars, reverse parking sensors, and tank level detection.
High Sensitivity Vibration Sensor Module (SW-1801P) | Shock & Shake Switch
Detect even the slightest tap. Unlike standard vibration sensors that require a hard shake, the SW-1801P High Sensitivity module can detect light knocks, impacts, and vibrations. Perfect for anti-theft alarms and "Smart Wake-Up" devices.
-
Sensor Type: SW-1801P (High Sensitivity Spring).
-
Output: Digital (High/Low).
-
Adjustable: Blue Potentiometer to set sensitivity trigger.
-
Best For: Anti-Theft Alarms, Earthquake Detection, and Smart Toys.
MQ-135 Air Quality & Hazardous Gas Sensor Module | CO2, Smoke, Ammonia
Detect smoke and dangerous gases instantly. The MQ-135 is the most versatile gas sensor for air quality monitoring. It detects a wide range of gases including Ammonia, Sulfide, Benzene, Smoke, and CO2. Perfect for "Smart Home" safety systems and environmental monitoring.
- Gases Detected: NH3, NOx, Alcohol, Benzene, Smoke, CO2.
-
Output: Analog (Gas Concentration) and Digital (Alarm Trigger).
-
Warm-up Time: ~20 seconds.
-
Best For: Air Quality Monitors, Smoke Alarms, and Industrial Safety.
MQ-2 Smoke & Gas Sensor Module | LPG, Butane, Hydrogen Detector
- Detects: Smoke, LPG, Propane, Hydrogen, Methane.
- Sensitivity: High (Adjustable).
- Response Time: < 10s.
- Best For: Fire Alarms, Gas Leak Detectors, and Industrial Safety.
Raindrop Sensor Module | Rain & Water Detector for Arduino
Build your own weather station. This sensor detects rain, snow, or water droplets. It consists of a large nickel-plated sensing board and a control module. When water hits the board, it sends a signal to your Arduino to close windows or sound an alarm.
-
Sensor Type: Resistive (Nickel-Plated Board).
-
Outputs: Digital (High/Low) and Analog (Rain Intensity).
-
Durability: Treated against oxidation for longer life.
-
Best For: Automatic Wipers, Smart Clotheslines, and Weather Stations.
Reviews
There are no reviews yet.